Noise analysis in direct detection and coherent detection phase-sensitive optical time-domain reflectometry systems.

This study compares noise and signal-to-noise ratio (SNR) in direct detection and coherent detection fiber-based distributed acoustic sensing (DAS) systems. Both detection schemes employ the dynamic analysis of Rayleigh-backscattered light in phase-sensitive optical time-domain reflectometry (ΦOTDR) systems. Through theoretical and experimental analysis, it is determined that for photodetection filters with a sufficiently narrow bandwidth, the SNR performance of both detection schemes is comparable. However, for filters with poor selectivity, coherent detection was found to exhibit superior performance. These findings provide crucial guidelines for the design of high-performance time-domain DAS systems.

Dynamic curvature sensing using time expanded ΦOTDR.

Shape sensing can be accomplished using optical fiber sensors through different interrogation principles such as fiber Bragg gratings, optical frequency-domain reflectometry (OFDR), or optical time-domain reflectometry (OTDR). These techniques are either not entirely distributed, have poor performance in dynamic sensing, or are only valid for few-meter-long fibers. Here, we present a system able to perform distributed curvature sensing with a range of 125 m, 10-cm resolution, and a sampling rate of 50 Hz. This is done by interrogating three cores of a multi-core fiber (MCF) with the novel, to the best of our knowledge, time-expanded phase-sensitive (TE-Φ)OTDR technique. This system fills a performance gap in fiber shape sensors, opening the door to applications in civil engineering, medicine, or seismology.

Time-expanded φOTDR using low-frequency electronics.

Time expanded phase-sensitive optical time-domain reflectometry (TE-φOTDR) is a recently reported technique for distributed optical fiber sensing based on the interference of two mutually coherent optical frequency combs. This approach enables distributed acoustic sensing with centimeter resolution while keeping the detection bandwidth in the megahertz range. In this paper, we demonstrate that TE-φOTDR can be realized with low-frequency electronics for both signal generation and detection. This achievement is possible thanks to the use of a couple of electro-optic comb generators driven by commercially available step recovery diodes. These components are fed by radio frequencies that are orders of magnitude lower than those involved in the signals so far originated by ultrafast waveform generation. The result is a simple, compact, low-cost and potentially field-deployable sensor that works without resorting to any decoding algorithm. Besides, high-resolution distributed sensing is carried out with no need of coding strategies or enhanced backscatter fibers. To check the capabilities of our system, we perform distributed strain sensing over a range of 20 m. The spatial resolution is 3 cm and the acoustic sampling rate can be increased up to 200 Hz. This performance reveals the prospective of the proposed approach for field applications, including structural health monitoring.

Dual electro-optic comb spectroscopy using a single pseudo-randomly driven modulator.

We present a dual-comb scheme based on a single intensity modulator driven by inexpensive board-level pseudo-random bit sequence generators. The result is a simplified architecture that exhibits a long mutual coherence time (up to 50 s) with no need of stabilization feedback loops or self-correction algorithms. Unlike approaches that employ ultrafast arbitrary waveform generators, our scheme makes it possible to produce long interferograms in the time domain, reducing the difference in the line spacing of the combs even below the hertz level. In order to check the system accuracy, we report two spectroscopic measurements with a frequency sampling of 140 MHz. All these results are analyzed and discussed to evaluate the potential of our scheme to implement a field-deployable dual-comb generator.

Cancellation of reference update-induced 1/f noise in a chirped-pulse DAS.

Distributed acoustic sensors (DAS) perform distributed and dynamic strain or temperature change measurements by comparing a measured time-domain trace with a previous fiber reference state. Large strain or temperature fluctuations or laser frequency noise impose the need to update such a reference, making it necessary to integrate the short-term variation measurements if absolute strain or temperature variations are to be obtained. This has the drawback of introducing a 1/f noise component, as noise is integrated with each cumulative variation measurement, which is detrimental to the determination of very slow processes (i.e., in the mHz frequency range or below). This work analyzes the long-term stability of chirped-pulse phase-sensitive optical time-domain reflectometry (CP-ΦOTDR) with multi-frequency database demodulation (MFDD) to carry out "calibrated" measurements in a DAS along an unmodified SMF. It is shown that, under the conditions studied in this work, a "calibrated" chirped-pulse DAS (CP-DAS) with a completely suppressed reference update-induced 1/f noise component is achieved capable of making measurements over periods of more than 2 months with the same set of references, even when switching off the interrogator during the measurement.

Virtual transparency in ϕ-OTDR using second order Raman amplification and pump modulation.

In distributed optical fibre sensors, distributed amplification schemes have been investigated in order to increase the measurement range while avoiding the limitation imposed by the fibre attenuation and the nonlinear effects. Recently, the use of Raman amplification with an engineered intensity modulation has been demonstrated as an efficient way to produce a virtually lossless trace employing a single-end configuration. In this paper, we propose the combination of this technique with a simultaneous second order Raman pumping scheme for increasing the measurement range. The optimal modulation profile has been numerically analyzed and we experimentally demonstrate a sensor able to detect perturbations along 70 km of fibre, with a minimal SNR penalty along the total length. Thanks to this new approach, the sensitivity in the worst point is considerably improved, and the ASD noise floor is also reduced. The measurement range is extended approximately 15 km compared with the equivalent first order pumping case.

Quadratic phase coding for SNR improvement in time-expanded phase-sensitive OTDR.

Time-expanded phase-sensitive optical time-domain reflectometry (TE-ΦOTDR) is a dual-comb-based distributed optical fiber sensing technique capable of providing centimeter scale resolution while maintaining a remarkably low (MHz) detection bandwidth. Random spectral phase coding of the dual combs involved in the fiber interrogation process has been proposed as a means of increasing the signal-to-noise ratio (SNR) of the sensor. In this Letter, we present a specific spectral phase coding methodology capable of further enlarging the SNR of TE-ΦOTDR. This approach is based on the use of a quadratic spectral phase to precisely control the peak power of the comb signals. As a result, an SNR improvement of up to 8 dB has been experimentally attained with respect to that based on the random phase coding previously reported.

Monitoring of a Highly Flexible Aircraft Model Wing Using Time-Expanded Phase-Sensitive OTDR.

In recent years, the use of highly flexible wings in aerial vehicles (e.g., aircraft or drones) has been attracting increasing interest, as they are lightweight, which can improve fuel-efficiency and distinct flight performances. Continuous wing monitoring can provide valuable information to prevent fatal failures and optimize aircraft control. In this paper, we demonstrate the capabilities of a distributed optical fiber sensor based on time-expanded phase-sensitive optical time-domain reflectometry (TE-ΦOTDR) technology for structural health monitoring of highly flexible wings, including static (i.e., bend and torsion), and dynamic (e.g., vibration) structural deformation. This distributed sensing technology provides a remarkable spatial resolution of 2 cm, with detection and processing bandwidths well under the MHz, arising as a novel, highly efficient monitoring methodology for this kind of structure. Conventional optical fibers were embedded in two highly flexible specimens that represented an aircraft wing, and different bending and twisting movements were detected and quantified with high sensitivity and minimal intrusiveness.

Time-expanded phase-sensitive optical time-domain reflectometry.

Phase-sensitive optical time-domain reflectometry (ΦOTDR) is a well-established technique that provides spatio-temporal measurements of an environmental variable in real time. This unique capability is being leveraged in an ever-increasing number of applications, from energy transportation or civil security to seismology. To date, a wide number of different approaches have been implemented, providing a plethora of options in terms of performance (resolution, acquisition bandwidth, sensitivity or range). However, to achieve high spatial resolutions, detection bandwidths in the GHz range are typically required, substantially increasing the system cost and complexity. Here, we present a novel ΦOTDR approach that allows a customized time expansion of the received optical traces. Hence, the presented technique reaches cm-scale spatial resolutions over 1 km while requiring a remarkably low detection bandwidth in the MHz regime. This approach relies on the use of dual-comb spectrometry to interrogate the fibre and sample the backscattered light. Random phase-spectral coding is applied to the employed combs to maximize the signal-to-noise ratio of the sensing scheme. A comparison of the proposed method with alternative approaches aimed at similar operation features is provided, along with a thorough analysis of the new trade-offs. Our results demonstrate a radically novel high-resolution ΦOTDR scheme, which could promote new applications in metrology, borehole monitoring or aerospace.

Towards Distributed Measurements of Electric Fields Using Optical Fibers: Proposal and Proof-Of-Concept Experiment.

Nowadays there is an increasing demand for the cost-effective monitoring of potential threats to the integrity of high-voltage networks and electric power infrastructures. Optical fiber sensors are a particularly interesting solution for applications in these environments, due to their low cost and positive intrinsic features, including small size and weight, dielectric properties, and invulnerability to electromagnetic interference (EMI). However, due precisely to their intrinsic EMI-immune nature, the development of a distributed optical fiber sensing solution for the detection of partial discharges and external electrical fields is in principle very challenging. Here, we propose a method to exploit the third-order and second-order nonlinear effects in silica fibers, as a means to achieve highly sensitive distributed measurements of external electrical fields in real time. By monitoring the electric-field-induced variations in the refractive index using a highly sensitive Rayleigh-based CP-φOTDR scheme, we demonstrate the distributed detection of Kerr and Pockels electro-optic effects, and how those can assign a new sensing dimension to optical fibers, transducing external electric fields into visible minute disturbances in the guided light. The proposed sensing configuration, electro-optical time domain reflectometry, is validated both theoretically and experimentally, showing experimental second-order and third-order nonlinear coefficients, respectively, of χ(2) ~ 0.27 × 10-12 m/V and χ(3) ~ 2.5 × 10-22 m2/V2 for silica fibers.

Long-Range Distributed Solar Irradiance Sensing Using Optical Fibers.

Until recently, the amount of solar irradiance reaching the Earth surface was considered to be a steady value over the years. However, there is increasing observational evidence showing that this quantity undergoes substantial variations over time, which need to be addressed in different scenarios ranging from climate change to solar energy applications. With the growing interest in developing solar energy technology with enhanced efficiency and optimized management, the monitoring of solar irradiance at the ground level is now considered to be a fundamental input in the pursuit of that goal. Here, we propose the first fiber-based distributed sensor able of monitoring ground solar irradiance in real time, with meter scale spatial resolutions over distances of several tens of kilometers (up to 100 km). The technique is based on an optical fiber reflectometry technique (CP-ϕOTDR), which enables real time and long-range high-sensitivity bolometric measurements of solar radiance with a single optical fiber cable and a single interrogator unit. The method is explained and analyzed theoretically. A validation of the method is proposed using a solar simulator irradiating standard optical fibers, where we demonstrate the ability to detect and quantify solar irradiance with less than a 0.1 W/m2 resolution.

Fast and direct measurement of the linear birefringence profile in standard single-mode optical fibers.

Phase birefringence in optical fibers typically fluctuates over their length due to geometrical imperfections induced from the drawing process or during installation. Currently commercially available fibers exhibit remarkably low birefringence, prompting a high standard for characterization methods. In this work, we detail a method that uses chirped-pulse phase-sensitive optical time-domain reflectometry to directly measure position-resolved linear birefringence of single-mode optical fibers. The technique is suitable for fiber characterization over lengths of tens of kilometers, relying on a fast measurement ($ {\sim} 1\,\, {\rm s} $∼1s) with single-ended access to the fiber. The proposed method is experimentally validated with three different commercial single-mode optical fibers.

Distributed sensing of microseisms and teleseisms with submarine dark fibers.

Sparse seismic instrumentation in the oceans limits our understanding of deep Earth dynamics and submarine earthquakes. Distributed acoustic sensing (DAS), an emerging technology that converts optical fiber to seismic sensors, allows us to leverage pre-existing submarine telecommunication cables for seismic monitoring. Here we report observations of microseism, local surface gravity waves, and a teleseismic earthquake along a 4192-sensor ocean-bottom DAS array offshore Belgium. We observe in-situ how opposing groups of ocean surface gravity waves generate double-frequency seismic Scholte waves, as described by the Longuet-Higgins theory of microseism generation. We also extract P- and S-wave phases from the 2018-08-19 [Formula: see text] Fiji deep earthquake in the 0.01-1 Hz frequency band, though waveform fidelity is low at high frequencies. These results suggest significant potential of DAS in next-generation submarine seismic networks.

Fiber-based distributed bolometry.

Optical fibers are inherently designed to allow no interaction between the guided light and the surrounding optical radiation. Thus, very few optical fiber-based technologies exist in the field of optical radiation sensing. Accomplishing fully-distributed optical radiation sensing appears then as even more challenging since, on top of the lack of sensitivity explained above, we should add the need of addressing thousands of measurement points in a single, continuous optical cable. Nevertheless, it is clear that there exists a number of applications which could benefit from such a distributed sensing scheme, particularly if the sensitivity was sufficiently high to be able to measure correctly variations in optical radiation levels compatible with the earth surface. Distributed optical radiation sensing over large distances could be employed in applications such as Dynamic Line Rating (DLR), where it is known that solar radiation can be an important limiting factor in energy transmission through overhead power cables, and also in other applications such as thermo-solar energy. In this work, we present the proof-of-concept of the first distributed bolometer based on optical fiber technology and capable of detecting absolute changes of irradiance. The core idea of the system is the use of a special fiber coating with high emissivity (e.g., carbon coating or black paint). The high absorption of these coatings translates into a temperature change that can be read with sufficiently high sensitivity using phase-sensitive reflectometry. To demonstrate the concept, we interrogate distinct black-coated optical fibers using a chirped-pulse ΦOTDR, and we readily demonstrate the detection of light with resolutions in the order of 1% of the reference solar irradiance, offering a high-potential technology for integration in the aforementioned applications.

Selective Monitoring of Oxyanion Mixtures by a Flow System with Raman Detection.

Raman spectroscopy is a selective detection system scarcely applied for the flow analysis of solutions with the aim of detecting several compounds at once without a previous separation step. This work explores the potential of a portable Raman system in a flow system for the selective detection of a mixture of seven oxyanions (carbonate, sulphate, nitrate, phosphate, chlorate, perchlorate, and thiosulphate). The specific bands of these compounds (symmetric stretching Raman active vibrations of carbonate at 1068 cm−1, nitrate at 1049 cm−1, thiosulphate at 998 cm−1, phosphate at 989 cm−1, sulphate at 982 cm−1, perchlorate at 935 cm−1, and chlorate at 932 cm−1) enabled their simultaneous detection in mixtures. Although the oxyanions’ limit of detection (LOD) was rather poor (in the millimolar range), this extremely simple system is very useful for the single-measurement detection of most of the oxyanions in mixtures, without requiring a previous separation step. In addition, quantitative determination of the desired oxyanion can be performed by means of the corresponding calibration line. These are important advantages for controlling in-line processes in industries like those manufacturing fertilizers, pharmaceuticals, chemicals, or food, among others.

Sidelobe apodization in optical pulse compression reflectometry for fiber optic distributed acoustic sensing.

We demonstrate a technique to reduce the sidelobes in optical pulse compression reflectometry for distributed acoustic sensing. The technique is based on using a Gaussian probe pulse with linear frequency modulation. This is shown to improve the sidelobe suppression by 13 dB compared to the use of square pulses without any significant penalty in terms of spatial resolution. In addition, a 2.25 dB enhancement in signal-to-noise ratio is calculated compared to the use of receiver-side windowing. The method is tested by measuring 700 Hz vibrations with a 140 nε amplitude at the end of a 50 km fiber sensing link with 34 cm spatial resolution, giving a record 147,058 spatially resolved points.

Long-range distributed optical fiber hot-wire anemometer based on chirped-pulse ΦOTDR.

We demonstrate a technique allowing to develop a fully distributed optical fiber hot-wire anemometer capable of reaching a wind speed uncertainty of ≈ ±0.15m/s (±0.54km/h) at only 60 mW/m of dissipated power in the sensing fiber, and within only four minutes of measurement time. This corresponds to similar uncertainty values than previous papers on distributed optical fiber anemometry but requires two orders of magnitude smaller dissipated power and covers at least one order of magnitude longer distance. This breakthrough is possible thanks to the extreme temperature sensitivity and single-shot performance of chirped-pulse phase-sensitive optical time domain reflectometry (ΦOTDR), together with the availability of metal-coated fibers. To achieve these results, a modulated current is fed through the metal coating of the fiber, causing a modulated temperature variation of the fiber core due to Joule effect. The amplitude of this temperature modulation is strongly dependent on the wind speed at which the fiber is subject. Continuous monitoring of the temperature modulation along the fiber allows to determine the wind speed with singular low power injection requirements. Moreover, this procedure makes the system immune to temperature drifts of the fiber, potentially allowing for a simple field deployment. Being a much less power-hungry scheme, this method also allows for monitoring over much longer distances, in the orders of 10s of km. We expect that this system can have application in dynamic line rating and lateral wind monitoring in railway catenary wires.

Phase-measuring time-gated BOCDA.

We demonstrate a simple scheme that allows performing distributed Brillouin phase spectrum (BPS) measurements with very high spatial resolution (∼7 cm) over long (∼4.7 km) optical fibers. This is achieved by inserting a Sagnac interferometer (SI) in a Brillouin optical correlation domain analysis (BOCDA) configuration. Over its already-presented time-domain equivalent (SI-BOTDA), this approach reduces the main source of noise (coherent backscatter noise) thanks to the low-coherence nature of the used signals. On the other hand, over the most usual schemes used for distributed BPS measurements, this implementation presents the key advantage of not requiring high-bandwidth detection or complex modulation while reaching unprecedented values of spatial resolution and number of resolved points for this type of measurement. Thanks to the linear dependence of the BPS feature around the Brillouin frequency shift, this scheme could also have the advantage of requiring shorter scanning ranges than amplitude-based configurations.

All-optical flip-flops based on dynamic Brillouin gratings in fibers.

A method to generate an all-optical flip-flop is proposed and experimentally demonstrated based on dynamic Brillouin gratings (DBGs) in polarization maintaining fibers. In a fiber with sufficiently uniform birefringence, this flip-flop can provide extremely long storage times and ultra-wide bandwidth. The experimental results demonstrate an all-optical flip-flop operation using phase-modulated pulses of 300 ps and a 1 m long DBG. This has led to a time-bandwidth product of ∼30, being in this proof-of-concept setup mainly limited by the relatively low bandwidth of the used pulses and the short fiber length.

Resolving 1 million sensing points in an optimized differential time-domain Brillouin sensor.

A differential pulse-width pair (DPP) Brillouin distributed fiber sensor is implemented to achieve centimetric spatial resolution over distances of several kilometers. The presented scheme uses a scanning method in which the spectral separation between the two probe sidebands is kept constant, while the optical frequency of the pump is swept to scan the Brillouin spectral response. Experimental results show that this method avoids detrimental temporal distortions of the pump pulses, which in a standard implementation prevent the DPP method from operating over mid-to-long distances. Such a novel scanning procedure allows the resolving, for the first time in pure time-domain Brillouin sensors, of 1,000,000 sensing points, i.e., 1 cm spatial resolution over 10 km in a conventional acquisition time.